News

Liquid Membrane Waterproofing for Terraces and Roofs

· Coating

Liquid Membrane Waterproofing for Terraces and Roofs

Short answer: before choosing a liquid membrane for a terrace or roof, answer one question: will the membrane stay exposed, or will it be covered with tiles, screed or soil? On exposed surfaces with foot traffic, a UV-resistant polyurethane membrane (DEMCO PUR 210 1K) or an elastic polyurethane coating protected by a UV topcoat (DEMCO PUR 340 FLEX) is used. On balconies and terraces that will be tiled or screeded, water-based and bituminous liquid membranes (DEMCO ELASTOMERİK 1K, ACR 250 W – 1K, BTM 400 2K, BPU 230) are used. For roof gardens, DEMCO BPU 230, which resists plant roots, stands out. The surface must be dry and sound, corners must be coved, and brush-applied membranes must be applied in at least two coats.

The values below are taken from the technical data sheets of DEMCO waterproofing products.

Exposed or covered?

SituationDEMCO productNote in the data sheet
Exposed terraces and roofs with foot trafficDEMCO PUR 210 1KHigh UV resistance; resistant to foot traffic and outdoor conditions
Exposed horizontal terraces with an elastic, decorative surfaceDEMCO PUR 340 FLEX + DEMCO PUR 412 TOP COAT UVProtected against sunlight with one coat of polyurethane topcoat; sags on vertical surfaces
Balconies, terraces and wet rooms under tiles or screedDEMCO ELASTOMERİK 1K · DEMCO ACR 250 W – 1KCovered with tiles, ceramics, plaster or screed after 3 – 4 days of curing
Terrace waterproofing under a covering, foundations and wet floorsDEMCO BTM 400 2KCovered within 3 days at the latest to protect it from the weather
Roof gardens and under-tile waterproofingDEMCO BPU 230Resistant to plant roots and chemicals in the soil; suitable for roof gardens
Large roofs and jobs that must be back in service quicklyDEMCO POLYUREA /PURE · /HBHot-sprayed by machine; see the polyurea guide

The data sheets of DEMCO ELASTOMERİK 1K and ACR 250 W – 1K also list flat and pitched roofs and sheet metal, zinc and galvanized surfaces among their areas of use. Covering with tiles, ceramics, plaster or screed is required only on terraces and in wet areas; on a roof the membrane can stay exposed. DEMCO ELASTOMERİK 1K resists sunlight at a thickness of 1 mm, and ACR 250 W – 1K is UV-resistant. For a roof that will stay exposed, define the thickness and details together with our technical team.

Products and consumption

ProductTypeCoatsConsumptionDrying
DEMCO PUR 210 1KOne-component polyurethane; cures with air humidity; elongation at break 300%2 – 3 coats0.600 – 0.700 kg/m² per coatTouch dry in 12 – 24 hours, full cure in 5 – 7 days
DEMCO PUR 340 FLEXTwo-component, solvent-free elastic polyurethane; self-leveling1 coat + topcoat1.300 – 1.500 kg/m² for 1 mm; topcoat 0.150 kg/m²Touch dry in 8 – 10 hours, full cure in 1 week
DEMCO ELASTOMERİK 1KOne-component, water-based elastomeric resin2 coats1.5 – 2 kg/m² in totalTouch dry in 3 – 4 hours, full cure in 7 days
DEMCO ACR 250 W – 1KOne-component, water-based acrylic copolymer2 coats1.5 – 2 kg/m² in totalTouch dry in 3 – 4 hours, full cure in 7 days
DEMCO BTM 400 2KWater-based, modified bitumen-rubber and cement; TS EN 15814, W2BAt least 2 coats1.50 kg/m² for 1 mm~12 hours between coats
DEMCO BPU 230Two-component bitumen-polyurethane; elongation at break > 1500%2 coats1.5 – 2 kg/m² in totalTouch dry in 4 hours, second coat after 1 day, fully dry in 7 days

Consumption varies with the roughness and porosity of the surface.

Application steps

  1. Surface: the surface must be dry, clean and sound. Dust, dirt, oil, rust and old paint are removed; holes, cracks and breaks are repaired with repair mortar. According to the DEMCO BPU 230 data sheet, concrete must have cured for 28 days. With DEMCO BTM 400 2K, PUR 210 1K and PUR 340 FLEX, the moisture content of the concrete must not exceed 4%.
  2. Corners and details: internal corners are coved with repair mortar and external corners are rounded. Reinforcement is used at details with a risk of cracking, such as wall–floor junctions; with DEMCO BTM 400 2K, a reinforcing mesh between coats is recommended on large areas.
  3. Primer: before DEMCO PUR 210 1K and PUR 340 FLEX, the concrete is primed with DEMCO EPOX 100 PR, and the membrane is applied about 24 hours later, once the primer is touch-hard. With DEMCO ELASTOMERİK 1K and ACR 250 W – 1K, absorbent and dusty surfaces are saturated with water and primed with a suitable primer. DEMCO BTM 400 2K is used with its own primer, DEMCO BPU 230 with a DEMCO epoxy or polyurethane primer suited to the surface.
  4. Mixing: one-component products are stirred at low speed for a few minutes before use. With two-component products, the components are first stirred in their own containers and then together.
  5. Coats: the membrane is applied in an even thickness by brush, roller or spray. With DEMCO ELASTOMERİK 1K and ACR 250 W – 1K, the second coat is applied at right angles to the first once the first has cured. With DEMCO BTM 400 2K, wait ~12 hours between coats; with DEMCO BPU 230, the second coat is applied after 1 day.
  6. Protection: the surface of DEMCO PUR 340 FLEX is protected against sunlight with one coat of DEMCO PUR 412 TOP COAT UV. Membranes that will be covered are covered with tiles, screed or plaster within the time in the data sheet (3 – 4 days for ELASTOMERİK 1K and ACR 250 W – 1K, 3 days at the latest for BTM 400 2K). Until then, the surface is protected from punctures, scratches and impact.

Points to watch

  • Ponding: DEMCO ELASTOMERİK 1K and ACR 250 W – 1K are not suitable for areas with pressurized water or ponding. On flat terraces, check the falls and drain details before application so that water runs to the drains.
  • Weather: do not apply in very hot, humid or windy weather, or on frozen surfaces or when there is a risk of frost. DEMCO BTM 400 2K is applied between +5 °C and +35 °C; after application the surface is protected from rain, dew and snow until it is fully dry.
  • Dew point and vapor pressure: with DEMCO BPU 230, the surface temperature must be at least 3 °C above the dew point and there must be no negative-side water vapor pressure.
  • Ambient humidity: with DEMCO PUR 210 1K and PUR 340 FLEX, ambient humidity must be below 65%.
  • Where not to use: DEMCO BTM 400 2K is not suitable for drinking water tanks or swimming pools. DEMCO PUR 340 FLEX runs and sags on vertical surfaces and is used on horizontal floors only.
  • Packaging: once opened, DEMCO PUR 210 1K must be used up quickly; the reaction continues even if the lid is closed, and the product can harden in the container.

Frequently asked questions

Which liquid membrane is used to waterproof a terrace?

If the membrane stays exposed, the UV-resistant DEMCO PUR 210 1K or DEMCO PUR 340 FLEX protected by a UV topcoat; if it will be tiled or screeded, DEMCO ELASTOMERİK 1K, ACR 250 W – 1K, BTM 400 2K or BPU 230.

How many coats of liquid membrane are applied?

Brush-applied membranes are applied in at least two coats. 2 – 3 coats are recommended for DEMCO PUR 210 1K; DEMCO ELASTOMERİK 1K, ACR 250 W – 1K and BPU 230 are applied in two coats totaling 1.5 – 2 kg/m², and DEMCO BTM 400 2K in at least two coats. The self-leveling DEMCO PUR 340 FLEX is applied in a single 1 mm coat with a UV topcoat on top.

When can tiles be laid on the membrane?

With DEMCO ELASTOMERİK 1K and ACR 250 W – 1K, after sufficient curing, 3 – 4 days later; with DEMCO BTM 400 2K the surface must be covered within 3 days at the latest.

Which product is suitable for roof gardens and green roofs?

DEMCO BPU 230 resists plant roots and chemicals in the soil, and its data sheet describes it as ideal for roof garden applications. Its elongation at break is above 1500%.

Can a liquid membrane be applied to a flat terrace where water ponds?

DEMCO ELASTOMERİK 1K and ACR 250 W – 1K are not suitable for areas with ponding. First correct the falls and drains of the terrace, then define a suitable system with our technical team.

Tell us the area of your terrace or roof, whether it will stay exposed or be covered, and the existing surface in the quote form, and our technical team will recommend a suitable membrane and quantity. For all products, see the insulation materials page.

All news

Colour charts

Standard colours of our floor coatings and paints, and granite epoxy options.

Colour charts

System lookup

Find the floor and coating systems that suit your sector and application.

Find a system

Let's talk

Let's discuss your needs for durable floor and coating solutions together.

Contact us
Follow us